Gillain & Co

• Range up to 115 mlc and capacity up to 500 m³/h.
• Robust design for high demanding applications.
• Gentle product handling
• Low energy consumption.
• EHEDG certified.
• Easy maintenance.
• Advanced impeller design with specially designed inlet ensuring product integrity and minimal NPSHr (Net Positive Suction Head required).

Download product sheet (PDF)

• Range up to 78 mlc and capacity up to 90 m³/h.
• Suitable for CIP and SIP.
• Internal surface finish: 0,5µm.
• EN 10204.3.1 and EHEDG certified.
• Elasotemers USP class 6.
• Full traceability.

• Highly efficient and economical design.
• Specially designed for filtration systems.
• Gentle product treatment.
• CIP.
• Available in 7 sizes.
• EHEDG certified.

Download product sheet (PDF)

• Highly efficient and economical centrifugal pump maximal inlet pressure up to 16 bar.
• Capacity 240 m³/h.
• Designed for CIP.
• Gentle product treatment.
• Chemical resistance.

• Range up to 115 mlc and a capacity up to 500 m3/h.
• Highly efficient and economical centrifugal pump.
• Gentle product treatment.
• Chemical resistance.
• Designed for use in the evaporation industry covering applications as liquid concentration and powder processing solutions as well as dewatering plant and equipment for the international dairy, food and beverage, ethanol, starch, pharmaceutical, chemical, alcohol and brewery industries.
• Available in 10 dimensions.
• Minimal tolerances and a low NPSH value. Pressure fluctuations caused by the process or by cavitation in combination with low NPSH value do not cause any problem.
• EHEDG certified.

• Range up to 115 mlc and a capacity up to 500 m3/h.
• Meets the requirements of the ATEX directive 94/9 IEC group II,
  categories 2 and 3, temperature class T3 and T4.
• Efficient and economical.
• Robust design for high demanding applications.
• Enlarged inlet and advanced impeller design providing an unimpeded product flowwith a very low NPSH required.
• Has been used for many years in very high demanding applications.
• EHEDG and ATEX certified.

• Range up to 115 mlc and a capacity up to 500 m3/h.
• Efficient and advantageous solution.
• Gentle product treatment.
• Chemical resistance.
• Specially designed for use in the evaporation industry covering applications as liquid concentration and powder processing solutions as well as dewatering plant and equipment for the international dairy, food and beverage, ethanol, starch, pharmaceutical, chemical, alcohol and brewery industries.
• Available in 10 dimensions.
• EHEDG certified.

Download product sheet (PDF)

• Range up to 87 mlc and capacity up to 85 m³/h.
• For simple transport duties.
• Cost-effective solution.
• Quick and easy maintenance.
• Utilizes the same mechanical shaft seal found in the LKH series, which is front-loaded and easily replaced without removing the backplate.
• EHEDG en 3A certifed.
• Extended 3-years warranty on all non wear parts on the condition that genuine Alfa Laval Spare Parts are used.

Download product sheet (PDF)
Regarder vidéo

• Range up to 87 mlc and capacity up to 84 m³/h.
• Specially designed for high demanding pharmaceutical applications.
• WFI (Water For Injection).
• Designed for CIP and SIP.
• Internal surface finition of 0,5µm.
• EN 10204.3.1 and EHEDG certificates.
• Full traceability.
• Extended 3-years warranty on all non wear parts on the condition that genuine Alfa Laval Spare Parts are used.

Download product sheet (PDF)

• Range up to 18 mlc and a capacity up to 13 m3/h.
• Specially designed for food, chemical,  pharmaceutical and other industries where acid resistant steel is resistant to the products to be pumped.
• Impeller of acid resistant steel 1.4404 (316L), nuts and yoke of stainless steel 1.4301 (304) and adaptor of cast iron.
• Seals are made of Nitrile (NBR).

Download product sheet (PDF)

• For simple applications in food, pharmaceutical, chemical and other industries where acid-resistant steel is resistant to the products to be pumped. 
• All product wetted parts, ie. pump casing, impeller and pump shaft, are
  made of acid-resistant steel 1.4404 (316L). Screws, yoke and nuts are
  made of stainless steel 1.4301 (304).
• Seals are made of nitrile (NBR).

Download product sheet (PDF)